ML50C-PV 1x50w 0-10V and push dimmable led driver 350mA to 1050mA multi-output 123x79x23.5mm for LED Panel Light
Feature
1, Output current and output voltage can be set by DIP switches, constant output current range from 350mA to 1050mA
2, Two circuit design AC-DC-DC, no flicckering in dimming 2%-100%
3, Stand-by power below 0.5W
4, Dimmable LED driver with primary PUSH, secondary PUSH and 1-10V dimming interface
5, Jumper design for switching different dimming modes, it is very convenient to select suitable dimming function as you required
6, Memory function: The driver has built-in permanent memory against power failure. Lights can return to previous dimming level when switch off and on again, even at mains restores
7, Synchronization: thanks to the MCU programme, up to 15pcs drivers should be controlled by the same switch. This means there is no need for any additional synchrony wire in larger installations, where many drivers should be controlled by one switch
8, Maximum length of the cable, from switch to last driver is 20m
9, Factory setting: 100% dimming level and 350mA output
10, Dim via a potentiometer
11, Support master-slave grouping net work
12, Protection: Short circuit / Over voltage / Over temperature
13, Long life span 50,000h, 5 years guaranty
14, Derating current for over high ambient temperature
Mechanical Specification
Dimming Operation:
1.Push button switch for dimming (see wiring diagram, Fig A & Fig B)
- ON/OFF: Short push (120ms ~ 1sec) on the switch
- Stepless dimming: Long push (＞1sec) on the switch. With every other long push, the light level goes the opposite direction.
- Synchronization: No need additional synchrony wire in larger installation, up to 15pcs drivers when connected to the same switch.
2.1-10V dimming (see wiring diagram, Fig C)
The driver supports any active 1-10V dimmer. When the dimming signal is less than 0.8V ~ 1V or short the dimming wires, the output of LED driver could be completely switch off, see Fig C
Specifications
| INPUT | Input voltage | 220-240Vac |
| Input frequency | 50-60Hz |
| Input current | 0.26A max |
| Power factor (Note 1) | ≥0.90 |
| Efficiency(Note1) | ≥86% |
| Stand-by power (Note 2) | ≤0.5W |
| OUTPUT | Output current/ voltage | 350mA 6~60V DC 21W max.; 500mA 6~58V DC 29W max 550mA 6~58V DC 31.9W max.; 650mA 6~58V DC 37.7W max. 700mA 6~58V DC 40.6W max.; 750mA 6~56V DC 42W max 850mA 6~56V DC 47.6W max.; 900mA 6~56V DC 50.4W max 1050mA 6~48V DC 50.4W max. 12V (0~1050mA) 12.6W max.; 24V (0~1050mA) 25.2W max. |
| Output load range | 50.4W Max. |
| Current accuracy | ±5% |
| Dimming mode | 1-10V, PUSH |
| ENVIRONMENT | Working temp.(Ta) | -20~50℃ |
| Surface temp.(Tc) | 85℃max |
| Working humidity | 20~85%RH non-condensing |
| Storage temp. | -40~80℃ |
| Life time | ≥50000hours |
| PROTECTION | Isolation class | Class Ⅰ |
| Protection class | IP20 |
| Over voltage | 300Vac, 2H |
| Short circuit | Protection type; auto reset |
| No-load | Protection type; auto reset |
| Over temperature | Protection type; auto reset |
| OTHERS | Safety | EN61347-1 EN61347-2-13 |
| EMC | EN55015, EN61000-3-2 |
| EN61000-3-3, EN61547 |
| Approvals | SEMKO, CE, RoHS |
| Withstand voltage | IN-OUT:3.75KVAC/5mA/1min |
| Dimension (L x W x H) | 123x79x23.8mm |
| Connection | Press-in type terminals, 0.75-1.5mm2 Input: L, N, PUSH, PE Output: SEC(+) SEC(-), 1-10V(+),1-10V(-) |
| NOTE | Note: 1, Power factor and efficiency is detected at 230Vac input and full load. 2, Standby power is detected at 230Vac input and switch off led load by push button. |
Applications
For LED panel light, LED down light, led strip, led tube etc…
Wire diagram
Product Tags:
|
|
ML50C-PV 1x50w 0-10V / Push LED Driver Dimmable 350mA - 1050mA Multi - Output Images
|
